N26/N26M/N26S Product Manual of Wireless Presenter

2023-03-08 14:05:26 admin

Wireless Presenter User’s Manual


Be sure to carefully read this user’s manual before using the wireless presenter and keep it for future reference.


Laser beams can cause permanent damage to the eyes. Do not look into  the laser beam or shine the laser beam into your eyes, other peoples’  eyes, or the eyes of pets. Be careful when pointing it towards  reflective surfaces.

Warning label for red laser product (See below figure):

Keep this device away from Children. This is a working tool, not a toy. It should only be used by adults.

Information in this document is subject to change without notice.

The seller may make improvements or changes in the product described in this document at any time.

Chapter 1    Introduction

I. Product description

A slim and lightweight wireless presenter. A perfect companion when you present. Thanks to the 100 meter range you can easily interact with your audience without fear of walking out of range. Thanks to the built in laser pointer, you can highlight the features you want your audience focused on.

The USB connector is securely fastened in the main body through the use of a magnet. And you can always change the AAA-battery whenever the built in led warns regarding low power. 

II. Features

1) PowerPoint, Keynote and Prezi support

The functions of page down and page up buttons can be switched between Page Down/Up, Left/Right Arrow and Up/Down Arrow, by pressing the page down and page up buttons at the same time.

2) RF frequency, which is an ISM free frequency and can be used world-wide.

3) Up to 100 meters’ wireless range. By using frequency hopping technology to improve the signal to noise ratio. It is Omni-directional and as such allows for the control of devices in other rooms.

4) The USB receivers can be controlled by 1 up to 6 transmitters.

5) Support functions including Page up and Page down,Full screen, Black screen.

6) Soft Silica Gel buttons allow for comfortable use.

7) Low power reminding function, the led will flash slowly when the power is low.

8) Storable receiver for easy carrying.

The USB receiver can be stored inside the wireless presenter.

9) Safe laser class complies with IEC/EN 60825-1:2014.

10) USB 2.0, plug and play.

11) Three ways to save power consuming by auto standby, deep sleeping and power switch.

12) One AAA battery, easy to replace.

13) The function of the keys can be customized by the Norwii Presenter software.

III. Operation system

Windows 7 / 8 / 10 / 11 or later, macOS/ Linux/ Android system. It may only support page turning function on Android/ Linux system.

IV. Package contents

1) Wireless presenter (USB receiver included) *1

2) User Manual*1

V. Specifications


Technology:             Radio Frequency

Frequency:               2.4GHz(N26/N26S)

Frequency:               868MHz(N26M/N26MS)

Control Distance:     up to 100m

Laser Power:           <1mW(Class 2) or <5mW(Class 3R), see the laser label on the back of the presenter.

Laser Distance:          >200m

Wavelength:              640-660nm

Battery:                      AAA Battery*1

Working Voltage:      1.5V

Dimension:                138.8*17.6*15mm

Weight:                      18.6g

USB Receiver

Working Voltage:      5V DC

Dimension:                24.68*13.8*5.14mm

Weight:                      1.6g

Chapter 2    Getting Started

VI. Function map

Without Tab and Enter key

With Tab and Enter key

Attention: When using this product, please change your Input Method Editors (IME) to English input mode.

VII. Function Description

1) Press and hold “Laser Pointer” button to turn on the laser, release button to turn it off.

2) Use the Microsoft PowerPoint to open PowerPoint files

3) Press “Page Up” button for 2 seconds to start a slideshow from the current slide. Press the button for 2 seconds again to escape from the full screen.

4) Press “Page Down” button and “Page Up” button to go forward and backward.

5) Press“Page Down” button for 2 seconds to enter into black screen. Press“Page Down” button for 2 seconds again to escape from the black screen

Note: When you press “Page Down” button for 2 seconds to enter the black screen, the USB receiver will send the letter ‘b’ or comma ‘,’ to the PowerPoint. If the Input Method Editor is open, the letter ‘b’ or comma ‘,’ will be intercepted and cannot be sent to the PowerPoint. In this case, try to turn off the IME or switch to the English input mode.

6) The presenter supports PowerPoint, Keynote and Prezi by switching the functions of the page down/up buttons. By default, the page down/up buttons of the presenter function as the Up/Down Arrow on keyboard, which can support PowerPoint and Keynote. By pressing the page down/up buttons at the same time, the function will change to the left and right arrows on the keyboard for Prezi support. Doing it a second time changes the function to page up and down, which supports many other programs. Pressing them together a third time will revert back to the default setting.

7) For hyperlink version N26S (Presenter with Tab and Enter key), If hyperlinks exist on the page, press “Tab” button to choose them, press “Enter” button to open the hyperlink.

After the hyperlink opened, you can keep pressing “Tab” button to switch opened windows. Release “Tab” button to choose the window. Keeping press “Enter” button to close the current window.

8) For products that support key function customization or spotlight serial products that support digital laser, spotlight, highlight, you need to download Norwii Presenter software. Please download it from the "Downloads" under the "Support" menu of Norwii official website www.norwii.com in English version.

VIII. Installation

1) Install battery

2) Take out the mini USB receiver from the wireless presenter.

3)Install the USB receiver

The operation systems including Windows, Android and Linux will install the driver for the USB receiver automatically.

4) Operate the wireless presenter When a button is pressed, the blue led on the wireless presenter will flash.

5) Turn off the wireless presenter.

Chapter 3    Frequently Asked Questions

1. How to know the battery is out of power?

Turn on the power switch of the presenter, then press laser button to check if the laser can be turned on. If the laser cannot be turned on, usually it means the battery is out of power or the laser diode is broken and need replacement.

In other case, If the LED on the wireless presenter starts to flash slowly, it means the power is low and the battery needs to be replaced.

2. Why does the laser pointer not work?

First, turn on the power switch. Second, check whether the wireless presenter is in low power or out of power. If the LED flashes slowly, it means the power is low and the battery needs to be replaced. If all the other buttons can work, only the laser pointer cannot work, the laser diode may need replacement. Third, check the place of anode and cathode of battery. Before putting a battery into the presenter, remember to remove the plastic cover of the battery.

3. Why does the computer does not detect the device when the USB receiver plugs into the PC?

Please check whether the USB works or not. You can use a USB mouse or keyboard to test the USB port. If a USB mouse or keyboard works on the USB port and the USB receiver of the presenter doesn’t work, it means the USB receiver of the presenter is broken or the USB drivers is not compatible with the USB receiver.

You can try another USB port of the same computer or USB ports of another computer to check whether the USB receiver of the presenter is good or not. If it works on other computer, it means the USB drivers of the computer are not compatible with the USB receiver. You need to back up your data and reinstall the OS.

4. The laser is ok and the USB receiver can be detected by the computer, why does the presenter cannot control the computer?

The reason is the USB receiver doesn’t save the presenter’s address properly. You can use Norwii Presenter software to do Pair operation to let the USB receiver to save the presenter’s address again.

5. How to grant permissions for Norwii Presenter on macOS?

On macOS, users need to add operation permissions of [Input Monitoring], [Screen Recording] and [Accessibility] for Norwii Presenter software under [System Preferences] - [Security & Privacy] - [Privacy]

IX. Certifications


Declaration of Conformity

This laser product complies with IEC/EN 60825-1-2014. Complies with 21 CFR 1040.10 and 1040.11, except for deviations pursuant to Laser Notice No.50, dated June 24, 2007.

Product Support

Shanghai Norwii Technology Co., Ltd

Address: No.277 Jinfeng Road, Pudong District, Shanghai, 201201, China

Tel: 86-21-51872080

Email: support@norwii.com